Тестер тормозной жидкости Ручка для проверки тормозного масла Ручка для проверки тормозной жидкости без упаковки

22*6*3cm 0.03kg

汽车刹车油检测笔 制动液测试笔

产品原理：

刹车油检测笔是根据电导率的变化来测定刹车油的水分变化。它通过发光二极管清晰地显示刹车油/制动液含水分的程度，含水分高会导致沸点降低，影响刹车性能。红光表示刹车油需要立即更换，绿光表示状态良好，黄光表示状态尚可，但快要更换了。

指示灯定义：

绿色LED灯＝制动液含水量小于1.5％，制动液合格

黄色LED灯＝制动液含水量等于1.5％、2％之间，刹车油品质达标，可以继续使用。

红色LED灯＝制动液含水量大于3％，制动液不能继续使用，需要更换

性能特点：

五个LED指示灯显示，测试结果更精准。

测试DOT 3，DOT4,DOT5刹车油

按下开关开启电源，绿色LED亮代表电池正常，绿灯不亮就代表要更换电池

自动关机功能

Brake Fluid Liquid Tester Auto 5 LED Car Vehicle Testing Tool

Many thanks for selecting this brake fluid tester.

The tester can be used as a digital brake fluid tester suitable for determining brake fluid quality. Developed for professional use in astomotive repair shops and in servicing. Quality is tested and included on five LEDs in terms of 'per cent of water in the brake fluid . '

Ready for Brake Fluid Test

Unscrew the brake fluid reservoir, and pull off the cap of the Brake fluid tester.Dip the test probes into the brake fluid up to the plastic rim of the device.

To check Fluid Quality

Press the button for power on, green LED will light up. Insert the tester into reservoir for one second then the tester result will be correctly indicated by LEDs.Repress the button for power off. The tester will automatically power off after about 15 seconds of inactivity.

Tester Specification:

1. To check the quality of brake fluid quality

2. 5 LEDs to indicate percentage of water in the brake fluid

3. Automatically power off

4. Operated by a LR03 AAA 1.5V battery (Not included)

Tester Instructions:

Brake fluid detection pen is based on the change in conductivity to determine the moisture change brake fluid. It shows clearly the extent of moisture contained by the light-emitting diode, high moisture content will lead to lower boiling point, affect braking performance. Red indicates the brake fluid needs immediate replacement, green represents good condition, yellow indicates the state is acceptable but soon replaced.

1. the green LED lights = water content in the brake fluid H2O <1.5%, brake fluid qualified

2. the yellow LED lights = brake fluid water content H2O = 1.5% to 3%, can continue to use, test again six months later

3. the red LED lights = water content in the brake fluid H2O> 3%, can not continue to use the brake fluid needs to be replaced Red LED: change brake fluid

4.LED red flashing: battery replacement

5.LED yellow: low moisture content, check again in six months

6.LED green: brake fluid lines / cell row

Tester Features:

Five LED indicators show the test results more accurate.

Testing DOT 3, DOT4, DOT5 brake fluid

Press the switch to turn on the power, the green LED light that represents the battery properly, the green light does not shine on behalf To replace the battery

Automatic shutdown

Technical parameters:

Green: Battery OK, that is, brake fluid does not contain water

Green / yellow: brake oil in water content of less than 1%, better brake fluid performance, ease of use.

Green / yellow / yellow: brake oil in water content of about 2%, brake fluid can continue to use.

Green / yellow / yellow / red: brake oil in water content of about 3%, the proposed replacement of brake fluid.

Green / yellow / yellow / red / red: brake oil in water content of at least 4%, the brake fluid must be replaced immediately responsible for very dangerous.

Attention:

1. Replace battery if the gree LED not light up any longer after you press power on button. Wash the test probe with tab water after use.

2.In case of skin contact with brake fluid, thoroughly wash the affected skin or clothing with water.

3.Do not expose brake fluid to the atmosphere for a long time as the fluid is highly hygroscopic!